1、邊框焊接，按邊框尺寸在地上定位。將邊框料的兩端寬邊上切成45。對接后點焊。校正無誤<方框的對角線要相等)后焊牢。

1. Weld the frame and position it on the ground according to the size of the frame. Cut the wide edges of both ends of the border material into 45 pieces. Spot welding after docking. Correctly correct (the diagonal of the box should be equal) and then weld it firmly.

2、中間長豎管焊接，每扇門3根長豎管，均勻分布在邊框內，定位間距為339毫米。擺放好位置后，先點焊，再校平，檢查無誤后再焊牢。

2. The middle long vertical pipe is welded, with 3 long vertical pipes for each door evenly distributed within the frame, with a positioning spacing of 339 millimeters. After placing it in place, spot weld it first, then level it, check for accuracy, and then weld it firmly.

3、矛頭用橫管焊接每扇門4根，夾在中問長豎竹之間、擺放好位置后，先點焊，再校平，檢查無誤后再焊牢:

3. The spear head is welded with a horizontal pipe, with 4 pieces per door, sandwiched between the long and vertical bamboo in the middle, and placed in the correct position. After spot welding, leveling, and checking for accuracy, it is welded firmly:

4、中間短豎管焊接，侮扇門4根，按圖樣中的位置擺好。先點焊，再校平，檢查無誤后再焊牢。

4. Weld the short vertical pipe in the middle, and place 4 doors according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly.

5、短橫管焊接每扇門24根，按圖樣中的位置擺好。先點焊，再校平，檢查無誤后再焊牢。為防l上焊接變形，可問隔焊。由于順序打亂，焊點較多，焊完后應檢查有無漏焊部位。

5. Weld 24 short horizontal pipes to each door and arrange them according to the position in the drawing. First spot weld, then level, check for accuracy, and then weld firmly. To prevent welding deformation on L, it is possible to ask for welding isolation. Due to the disordered sequence and a large number of welding points, it is necessary to check for any missed welding areas after welding.

6、槍頭焊接依次將各槍頭分別焊在相應的位置上，要求與橫桿垂直，正面朝前，不能扭曲。

6. Weld the gun heads in their respective positions in sequence, ensuring they are perpendicular to the crossbar, facing forward, and not twisted.

7、花形焊接把所有花形分別擺放在相應位置上，看是否合適，調整無誤后，先點焊到框架上，整體再檢查一遍，然后焊牢。

7. Flower welding: Place all flower shapes in their respective positions to see if they are suitable. After adjusting them correctly, spot weld them onto the frame first, inspect the overall structure again, and then weld them firmly.